| MATERIAL SAFETY DATA SHEET |
SECTION I : PRODUCT IDENTIFICATION |
|
Product Name:
|
Resinoid, rubber and shellac bonded products
|
|
with or without fibreglass reinforcement
|
|
| HAZARD RATING: |
| Health |
 |
| Reactivity |
 |
| Flammability |
|
|
SECTION II : MATERIALS AND COMPONENTS
|
| Product may contain some of the following ingredients: |
INGREDIENTS
(only some may be used)
|
CAS NUMBER |
MAX WEIGHT % |
OSHA PEL mg/m3** |
ACGIH TLV mg/m3** |
CARCINOGEN |
| Aluminum Oxide (Alumina) |
1344-28-1 |
95 |
N/A |
10 |
N |
| Titanium Dioxide |
13463-67-7 |
4 |
5 |
5 |
N |
| Silicon Carbide |
409-21-2 |
95 |
15 |
10 |
N |
| Zirconium Dioxide |
7440-67-2 |
25 |
5 |
5 |
N |
| Phenol Formaldehyde (Resin) |
9003-35-4 |
18 |
N/A |
10 |
N |
| Furfural |
98-01-1 |
5 |
2 |
2 |
N |
| Potassium Fluroborate |
14075-53-7 |
5 |
2.5 |
2.5 |
N |
| Calcium Fluoride (Fluorspar) |
7789-75-5 |
20 |
N/A |
2.5 |
N |
| Iron Oxide |
1309-37-1 |
8 |
10 |
5 |
N |
| Calcium Oxide (Lime) |
1305-78-8 |
4 |
5 |
2 |
N |
| DPR Rubber |
78-79-5 |
5 |
N/A |
N/A |
N |
| Iron Disulphide (Pyrites) |
12068-85-8 |
20 |
N/A |
N/A |
N |
| Zinc Sulfide (Sachtolith) |
1314-98-3 |
15 |
15 |
15 |
N |
| Paraffin |
N/A |
10 |
N/A |
2 |
N |
| Fibreglass |
N/A |
10 |
N/A |
10 |
N |
** Total Dust
SECTION III: PHYSICAL PROPERTIES
|
|
Boiling Point:
|
N/A
|
Specific Gravity:
|
>1
|
|
Melting Point:
|
N/A
|
Solubility in Water:
|
N/A
|
|
Freezing Point:
|
N/A
|
Solubility in Alcohol:
|
N/A
|
|
Vapor Pressure:
|
N/A
|
Solubility in other
Solvents:
|
N/A
|
|
Vapor Density:
|
N/A
|
Evaporation Rate:
|
N/A
|
|
Appearance:
|
Solid
Product
|
Odor:
|
Possible
during use
|
SECTION IV: FIRE AND EXPLOSION DATA
|
|
Flash Point:
|
N/A
|
No
Special Fire Fighting Procedures
|
|
Flammable Limits:
|
N/A
|
No
Need to Extinquish
|
|
Explosion Potential:
|
N/A
|
|
SECTION V: REACTIVITY DATA
|
|
Stability:
|
Stable
|
Incompatibility:
|
Avoid strong acids
|
|
Conditions to Avoid:
|
N/A
|
Polymerization:
|
Will not occur
|
|
Decomposition
Products:
|
Dust, Organic Fumes
|
|
|
SECTION VI: HEALTH HAZARD INFORMATION
|
|
Inhalation:
|
Acute effects - coughing, shortness of breath;
Chronic effects - may effect breathing;
|
|
Ingestion:
|
No known adverse effects;
Ingestion not recommended;
Get medical attention;
|
|
Skin
|
Some may experience skin irritation from dust;
Wash affected areas with soap and water;
Get medical attention;
|
|
Eye
|
Dusts may irritate eyes; Flush with large amounts of water;
Get medical attention;
|
SECTION VII: SPECIAL PROTECTION INFORMATION |
- Use only in compliance with ANSI B7.1-2000 (Safety Requirements)
- Use with proper ventilation.
- Eye protection recommended.
- Protective gloves may be used if desired.
- Use dust respirators; avoid breathing dust.
- Wash thoroughly after handling.
- Normal clean-up procedures.
- Waste disposal method: standard landfill methods.
|
|
Prepared By
|
|
Date.......1/3/2008.......
|
Note: The above information is accurate to the
best of our knowledge, however, since data, safety standards, and government
requirements are subject to change and the conditions of handling and use, or
misuse are beyond are control, Buffalo Abrasives, Inc. makes no warranty,
either expressed or implied, with respect to the completeness or continuing
accuracy of the information contained herein and disclaims all liability for
reliance thereon. User should satisfy
himself that he has all current data relevant to his particular use.
|
